Procedure – Powder/Chip Samples

Prepare the instrument as outlined in the operator's instruction manual.

Login a minimum of three Blank reps.

Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open. Insert a *** Nickel Capsule (leave capsule open) into the open port at top of loading head.

Note: samples using automation should be placed in the appropriate autoloader position before starting the analysis sequence. Once the sequence has started, the automatic analysis will start and end automatically.

氧氮氫分析儀的常見故障及解決方法：

氧和氮空白值超過20。這是由于氣流小，不能將爐子中的空氣驅趕出去?？烧{節氣體流量，調節載氣壓力在0.2~0.4MPa。接通儀器載氣，放一個石墨坩堝在下電極上，打開主電源開關，點擊軟件上的關爐按鈕，關閉爐子并等待10s。調節流量調節器，直到流量計a顯示為30L／h，打開爐子。調節調節器直到流量計b顯示為50L／h，再次關閉爐子。如果以上設置不穩定，則增加流量至100L／h，反復調節直至儀器穩定。 上海進口分析儀優惠價格強力內循環水冷裝置。

Procedure – Powder/Chip Samples

Instrument calibration/drift correction.

Calibrate/drift following the procedure outlined in the operator's instruction manual.

Login Sample with the appropriate number of reps.

Weigh approximately *** grams of appropriately prepared sample into a *** Nickel Capsule, enter mass and sample identification into appropriate rep fields. If applicable, place the nickel capsule in the

appropriate autoloader position.

Repeat steps 3c through 3i for sample analysis.

儀器的亮點和優勢：

特點和優勢

·爐頭區域LED照明系統

·爐頭快速拆裝的粉塵過濾裝置

·裝有自動旁路閥的可快速拆裝氧水捕集裝置

·**的動態流量補償（DFC）保證熱導池氣體流量、壓力恒定

高效脈沖爐冷卻系統

·強力內循環水冷裝置熱交換效率

·雙直流風扇保證持續冷卻，不受電壓波動的影響

·***電極爐頭設計，提高脈沖爐

全自動分析系統（可選）

·自動清掃裝置

·20位或100位全自動分析系統

·高效全自動真空除塵裝置直接將粉塵排至儀器外部捕集器中，消除環境污染

改進的紅外檢測池技術

·***紅外池的恒溫絕熱技術消除了外界環境溫度的干擾

·長壽命的紅外發射光源和無漂移的電路設計保證紅外檢測池的長期穩定性

·氧高低雙量程采用3個碳紅外檢測器同時檢測一氧化碳和二氧化碳，保證準確定量 Cornerstone氧氮氧分析軟件允許用戶在單一分析界面中完成日常的所有工作，快速而且簡單易用。

ONH836氧氮氫分析儀

高頻燃燒紅外檢測技分析無機材料中的碳、硫含量。

采用惰性氣體保護熔融法，提供各種無機材料、鋼鐵、有色金屬、硬質合金、難熔金屬、陶瓷等材料中寬范圍的氧氮氫同時分析。

該儀器配置MS Windows®的軟件接口，專為觸摸屏操作定制。長期的開發研究與客戶反饋相結合，這個簡單方便的軟件使得用戶可以快速完整訪問儀器控制，分析設置，故障診斷，數據報告， **提高日常分析的效率并節省用戶寶貴的時間。 可選的Cornerstone® Mobile軟件功能，使得用戶可以在手機，便攜式電腦及臺式電腦上便捷的訪問儀器數據，分析曲線圖形以及儀器的狀態，實現對儀器的遙控。

Cornerstone氧氮氫分析軟件分成4個主要部分：分析、診斷、設定、儀器，界面可快速導航和組織。安徽進口分析儀咨詢報價

分析軟件同時包括實時的環境參數的監測，提供完整的系統圖表的模擬。江蘇美國分析儀廠家供應

Method Selection

Two methods are described in this application note; either method can be used to analyze iron, steel, nickel-, and cobalt-base alloys. The Precision Method is recommended for general use and will provide the best precision and accuracy throughout the typical O, N, and H concentrations found in this group of metals; approximate cycle time is 3.5 minutes. The Fast Track method can be used where speed of analysis is a critical component; for example, when molten metal is being sampled and results are required in the shortest possible time. This method will produce suitable results for most samples; approximate cycle time is 2.25 minutes. As noted above, sampling and sample preparation are key elements to accurate O, N, and Hdetermination as well. It is up to the user to determine which method best meets their needs.

江蘇美國分析儀廠家供應